EG Aircraft thanks you for your purchase and wish you much fun with the De Havilland DH-89 "Dragon Rapid"
AIRCRAFT REZZING
1 / Drag the item " DH-89 Dragon Rapide EG Aircraft" from your inventory to the ground
2 / Accept the attachement invitation for the HUD
3 / You can edit this silhouette to set it on the spot where you want the plane to be rezzed. (Do not change the height)
4 / click "Rezzing" on the HUD to rezz the plane.
5 / After use, to remove the aircraft properly, click again on the button "Rezzing" on the HUD (the aircraft being "copy" it remains an original in your inventory)
SITTING IN THE AIRPLANE
Note: The side door opens and closes simply by clicking on it (single left click).
1 / To sit, right click and then sit on the ball "Pilot".
2/ The aircraft offers to accept the attachment, do so.
3 / To leave you seat, click "Standup" ON THE HUD.
HUD CONTROLS
the buttons from left to right
1 /[Position L] toggles on/off the nav lights
2 / [Landing L] toggles on/off the landing light
3 / [Strobes] toggles on/off the strobes
4 / [Cabine L] toggles on/off the cabin light
5 / [Rezzing] Rezzes or removes the aircraft
6 / [Standup] To get up
7 / [Default] Default Camera
8 / [Follower] Dynamic following camera (you can zoom in or out)
9 / [taxiing] Camera in above position ideal for taxiing
10 / [Blocked] Freezes the camera on the spot it is when you click. It allows you to fly the plane, looking from the ground. (Be carefull about your drawing distance)
THE FLIGHT INSTRUMENTS FROM LEFT TO RIGHT
1 / Airspeed indicator indicates your flight speed (in mph)
2 / Attitude indicator, shows the flight attitude
3 / Heading indicator indicates your heading (in degrees)
4 / Vertical speed indicator (VSI) indicates the rate of climb or descent (in meters / second)
5 / Altimeter indicates altitude (in meters)
ENGINES
1 and 2 / Ignition for right and left engine (automatic start)
below there are two power indicators (dial and digital)
GPS
shows your location on the regions of Blake sea, nautilus, uss, and Corsica.
Z-map zooms out, Z + zooms the map in.
FLIGHT CONTROL KEYPAD
1 / Up "arrow down" and down "arrow up"
2 / Turn right or left, respectively "right arrow" or "left arrow"
3 / "Pgup/PgDown" increase -reduce the power
CHAT COMMANDS
startl: Start the left engine
Startr: Start the right engine
Stopl: Stops the left engine
stopr: Stops the right engine
b: Engages or looses the brakes (until the complete stop of the aircraft )
l: Toggles nav lights
s: Toggles strobe lights
ld: Toggles the cabin light
p: Toggles landing light
The engine power can be controlled directly by chat command
0 = 0%
1 = 10%
etc etc up to ...
10 = 100%
These chat commands allow you to reach the desired power directly without having to go through all the steps successively
TAXIING
Once seated in the aircraft:
1 / Turn your nav lights on to show other users that the aircraft is under control.
2/ If ATC is available, contact them and ask for instructions and take off clearance for your flight.
3 / Start the engine
4 -/ Press PgUp up to a maximum of 30% power or use the appropriate chat commands (indicating chat)
Note: from 50 mph you risk injury, but you can use this power in a straight line (only) to save time.
5 / Aim the plane with the left and right arrows to the runway to take off following the instructions of the Airport controler
TAKE OFF
1/ Taxi to the runway
2/ Align the aircraft on the runway heading, and hold.
3 / Enable the brakes by chat command "b" and wait for the complete stop of the airplane (speed 0 mph) and wait for takeoff clearance from the tower.
4/ Increase power up to 100%, then release the brakes by chat command "b"
5 / Reaching 85 mph you can rotate and climb.
LANDING
As for takeoff, contact the ATC and ask for instructions and necessary clearance for your landing.
1/ Align the aircraft on the centerline of the runway at an altitude between 70 and 100 m and at a good distance (minimum 200m)
2/ Reduce power down to 10%
3/ Hold the aircraft descending towards the runway. (A descent of less than -1 in variometer is unsafe for landing)
4/ touchdown (0 VSI), reduce the throttle down to 0%, you can use the brakes when landing too long)
5/ Taxi to your parking area following the indications of ground control.
NOTE: Your plane can fly through full parcels
-------------------------------------------------- -----------------------
BEST SCLUPTIES RENDERING
===================
For a correct display of your sculpties, see below.
LOD debug: Debug your settings LOD is a setting that will bring up all your sculpties perfectly. Just follow these steps:
1. Open the "Advanced" menu by Ctrl-Alt-D, or Opt-Ctrl-D on Mac.
2. Select "Debug Settings" in the list.
3. In the blank field, copy and paste this text:
RenderVolumeLODFactor
4. It is recommended to choose a value between 4 and 6.
Thanks to Ghanni Lane!
To contact us in world:
Erick Gregan
Kahlan Bingyi (sales and special orders)
Serena Lexington (demo's and technical questions not answered on the website)
Note: EG Aircraft (Erick Gregan) can not be held responsible for any changes made by © Linden Research, Inc. to "Second Life" or any malfunction during the operation of the airplane with the quality of service offered by © Linden Research, Inc..
